Tender For supply of trans case assembly part no- 116 tm 03003,valve assembly part no- 116 tm 03117,gear forward driven part no- 116 tm 03077,gear and pinion set part no- 116 tm 03028,intermediate shaft assembly part no- 116 tm 03199,gear driven forward part no- 116 tm 03085,gear driven reverse part no- 116 tm 03093,gear driven 4th part no- 116 tm 03069,gear driven 3rd part no- 116 tm 03052,gear driven 2nd part no- 116 tm 03044,gear driven 1st part no- 116 tm 03036,bearing cage assembly part no- 116 tm 03174,gear shaft fork assembly part no- 116 tm 03214,gear shift lever assembly part no- 116 tm 03222,lever assembly f and r part no- 116 tm 03247,change lever assembly part no- 116 tm 03255
Tender For supply of spare parts of scania - hose nipple part no 225678, nipple part no 225679, container part no 275584, intermediate part part no 219516, expansion tank part no 389240, draining tube m,erf 420mm part no 813588, drain cock (tap) part no 228491, hollow screw part no 17384, ferrule part no 128034, exhaust piping part no 253709, plug part no 244465, spring centre coupling part no 395182, ball bearing part no 214363, rubber string part no 361112, rubber string part no 294794, disk, outer part no 194428, pinion (speedometer drive) part no 174806, gear shaft part no 174786, switch part no 328655, cylinder(t/g box) part no 244047, elbow nipple part no 140548
Tender For supply of spare parts of scania - hose nipple part no 225678, nipple part no 225679, container part no 275584, intermediate part part no 219516, expansion tank part no 389240, drain cock (tap) part no 228491, tube part no 257352, tube part no 391463, hollow screw part no 17384, exhaust piping part no 253709, plug part no 244465, spring centre coupling part no 395182, ball bearing part no 214363, rubber string part no 361112, rubber string part no 294794, disk, outer part no 194428, pinion (speedometer drive) part no 174806, gear shaft part no 174786, switch part no 328655, cylinder(t/g box) part no 244047, rubber clamp part no 5340176327(813933)
Tender For corrigendum : supply of first intermediate pinion hold back pinion for kcn450 gearbox part no kcn450hbp402 , second intermediate pinion fitted with second intermediate wheel for kcn450 gearbox part no kcn450ip302iw403 , output shaft for kcn450 gearbox part no kcn450ops202 , output wheel for kcn450 gearbox part no kcn450opw303 , hold back for kcn450 gearbox part no kcn450hb480
Tender For sic of submersible pump set and all allied e/m equipment for rebored tube well near h.no.-116c shahpur jat in greater kailash constituency ac-50. - supply of submersible pump set fitted with dynamically balanced ss impeller mounted on stainless steel shaft with protection sleeve having stage bowl & closed grained shorted type impeller, the pump will be directly coupled to required wet type induction motor of 7.5 hp, 10 stage, speed 2900 rpm suitable for operation of 3 phase, 415 volt, 50 hz, ac supply with efficiency 70% at following duty point:200 lpm on 90 mtr. head. having discharge outlet 50 mm and outside dia 142 mm.make: bs/skope/ any djb approved make, supply of hut type electrical feeder pillar / fabricated with 50 x 50 x 6mm angle iron and 16 swg ms sheet with horizontal and vertical intermediate member of suitable size. i.e. 1370 mm x 760mm x 460 mm. with arrangement for mounting of switchgear and electrical energy meter i.c. painting heaving following item fitted.a) mccb 63 amp, 4pole, 415volt, 35 ka -1 no.b) rccb 63 amp, 4pole with earth fault indication protecting a circuit automatically in the event of earth leakage sensitivity 100ma, - 1 noc) fully automatic star delta starter of relay range 13-21 amp. (7.5 hp to 10 hp) 3 phase oil immersed type -1 no.d) ampere 96 x 96 mm. square shape 0-30 amp-1 no.e) voltmeter 96 x 96 mm. square shape 0-500 volt-1 no.e) indicating lamp (a set of 3 lamps) 1.setf) shunt capacitor of 10 kvar mpp type with three phase isolator with suitable bankingg) motor protection assembly with earth leakage protection phase sequence corrector, single phasing, protection, overload protection, high voltage / low voltage protection time delay power on, programmable time switch i.c. r&b phase facility to change over from automatic, to manual &vice verse for up to 10 h.p -01 nos. complete wiring & installation of above accessories with required copper conductor wire and thimble etc. 01 job.make of all components: any djb approved., s/o pvc insulated & pvc sheathed cable with plain copper conductor having 3 phases, 3 core flat for submersible motor of 4 square mm size each 100 mtrs.make:grandlay / havells./any djb approved make, s/o m.s. clamp of 600 mm length duly fabricated out of 12.5 mm thick 75 mm wide, m.s. plate for holding the pipe of 50 mm dia., s/o double flange gi column pipe 50 mm dia medium class each of 3 mtrs long duly threaded on both ends, welded fitted with gi flange on both ends with slot of submersible cable. make: tata/ jindal./any djb approved make, s/o/ tail piece of the medium class gi pipe 500 mm long with one end threaded as per outlet of pump & another end flanged as per size of gi pipe 50 mm dia., s/o gi 90 bend of size 50 mm dia having both side flange (heavy duty)., s/o nut & bolts of 1/2 dia of different size i.e. 1.5 dia& 2.5 long full threaded., s/o rubber packing for 50 mm dia flange., fabrication and supply supply of bore cover approx size 8-10 inch diameter made out from 6mm thick m.s. sheet in 2 halves & a circular hole in centre 3-1/2 dia. with locking arrangement by nuts & bolt., earthing with g.i. earth pipe 4.5 meter long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required., providing and fixing 6 swg dia g.i. wire on surface or in recess for loop earthing as required., installation of t/well by lowering of sub p/set with all allied above items. this includes installation and grouting of panel boards with all electrical wiring & cabling at site. all tools & tackles i/c. tripod chain pulley blocks etc. shall be arranged by the firm. this includes testing & commissioning of t/well on load at site i/c. cartage, loading & unloading of material. it also includes a trial run of 30 hrs operation successfully by the firm. all required civil work included in the scope of work.